Laser beam is not visible due to bright light When visibility is no longer an issue (during night-time, for instance), you can go back to using the older battery.
#LEVELFIX LASER PRO#
Pro Tip – Always carry an extra pair of batteries and use them for such emergencies. Fresh batteries give out more output, causing the level to pulse a brighter beam. In a line laser level, you can improve visibility by using a freshly (newly) charged battery or a fresh pair of alkaline batteries. This will increase the intensity of the laser beam and make it stronger and more visible, even in daylight. What to do if I have low visibility?Ī quick solution is to reduce the speed of the motor in a rotary laser level. You should consult the service care and not engage in opening the case. If there is no mechanical switch, it might be a loose bolt or some other small component. Johnson levels (model number - 40-6530) are known to have this function. Try changing the alignment and the sound should go. If yes, then it’s not an issue but the sound of the mechanical switch which helps you distinguish between horizontal and vertical alignment. Inspect if the clicking noise only comes when you switch on the device. I hear a clicking noise in my laser level. If you are a daily/frequent user, get in touch with PLS Support. If the battery discharge is too high, you will have to remove the battery after each usage to preserve the power. How can I avoid battery discharge in my PLS 180? This trick works most of the time across types of batteries such as Ni-MH and Li-ion. A workaround to this is to completely discharge it (by using the device till the time it refuses to switch on) and then recharge it to 100%.
#LEVELFIX LASER FULL#
Did you use your device for a few hours and then used it months later? In such a scenario, it is possible that the battery does not reach full charge. If it does, you can confirm that the battery is dead. A good way to check this is to connect your device to an AC/DC adapter/power supply and see if the device works for a longer period. The most common is that the battery may be dead and no longer capable of holding power. Why does my rechargeable battery drain quickly? Use a q-tip and wrap an alcohol wipe around it, then clean the contacts in the battery container. If it still shuts off automatically, the problem could be with the contacts.
#LEVELFIX LASER HOW TO#
How to fix my level that is repeatedly turning off?įirst, check and replace the battery. If the problem persists, try resetting the level. This is mostly an issue with the battery, where the device is indicating low power. If the laser level is mishandled or has fallen on the floor, recalibration is important to achieve accuracy. You may need to follow the instructions/guidelines shared by your manufacturer for better calibration and subsequent troubleshooting. Adjust the level vial accordingly and repeat the process until the distance is within the limit.If the distance between B+ and C+ is more than what is specified in your device’s manual, you will need to calibrate Rotate it at 90 degrees and make another marking, C+.If these markings are not on the same level, the center point (mark it as B+) will be considered true level.Rotate it at 180 degrees and repeat the process.Turn on the device and make it face a wall.Try checking the power source.įollow these steps to calibrate or recalibrate your rotary level: The light source may be broken or it is not getting sufficient power. If the problem persists, try changing the batteries of the remote.
Make sure you are in the direct vicinity of the device while trying to remote control it. Laser level remote controller needs to be present in the line of sight (LOS) to work. Pro Tip – In case of mild corrosion of laser level parts, use anti-rust ointments like WD-40.
#LEVELFIX LASER PROFESSIONAL#
Such problems will require proper diagnosis and professional assistance. This could also be caused due to eroded joints (rotary laser) or missing parts due to a fall. Try lightly shaking the device and see if there are any loose parts. In either case, it is best to consult the repair center (of the manufacturer). If you feel something’s stuck, the rigging or the compensator could be damaged. If it works, then you need to dispose of the battery immediately and replace it.Ĭheck if the laser head can be manually rotated. If your laser level supports direct charging, try connecting the device to an AC/DC input and using.
Replace it with a new or freshly charged one. What to do basic troubleshooting?įew steps to follow before using an advanced solution or calling the repair center:Ĭheck the power source. Each question carries a problem, which is then answered with one or more solutions, starting with the best and the easiest one. To make this guide easier to follow, we have structured this in a question-answer layout. Laser Level Stops Working – A General Troubleshooting Guide
0 kommentar(er)
